bonjour,je souhaite que la RTC declenche une interruption sur le pin 2 de l'arduino UNO.
J'ai d'abord essayé par scrutation,ça fonctionne:
Code : Sélectionner tout - Visualiser dans une fenêtre à part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
const uint8_t alarmInput(2);
 
void setup()
{
    Serial.begin(9600);
    pinMode(2, INPUT_PULLUP);
 
    // initialize the alarms to known values, clear the alarm flags, clear the alarm interrupt flags
    RTC.setAlarm(ALM1_MATCH_DATE, 0, 0, 0, 1);
    RTC.setAlarm(ALM2_MATCH_DATE, 0, 0, 0, 1);
    RTC.alarm(ALARM_1);
    RTC.alarm(ALARM_2);
    RTC.alarmInterrupt(ALARM_1, false);
    RTC.alarmInterrupt(ALARM_2, false);
    RTC.squareWave(SQWAVE_NONE);
    // set Alarm 1 to occur at 5 seconds after every minute
    RTC.setAlarm(ALM1_MATCH_SECONDS, 5, 0, 0, 0);
    // clear the alarm flag
    RTC.alarm(ALARM_1);
    // configure the INT/SQW pin for "interrupt" operation (disable square wave output)
    RTC.squareWave(SQWAVE_NONE);
    // enable interrupt output for Alarm 1
    RTC.alarmInterrupt(ALARM_1, true);
    Serial.println(" Start ");
    //attachInterrupt(digitalPinToInterrupt(2),printTime,LOW);
}
 
void loop()
{
    // check to see if the INT/SQW pin is low, i.e. an alarm has occurred
  if ( !digitalRead(alarmInput) )
    {
        printTime();
 
    }
 
}
 
void printTime()
{
       RTC.alarm(ALARM_1);
       Serial.println("ça marche");
 
}
Par contre lorsque je fonctionne par interruption:

Code : Sélectionner tout - Visualiser dans une fenêtre à part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
#include <DS3232RTC.h>        // https://github.com/JChristensen/DS3232RTC
 
// pin definitions
const uint8_t alarmInput(2);
 
void setup()
{
    Serial.begin(9600);
    pinMode(2, INPUT_PULLUP);
 
    // initialize the alarms to known values, clear the alarm flags, clear the alarm interrupt flags
    RTC.setAlarm(ALM1_MATCH_DATE, 0, 0, 0, 1);
    RTC.setAlarm(ALM2_MATCH_DATE, 0, 0, 0, 1);
    RTC.alarm(ALARM_1);
    RTC.alarm(ALARM_2);
    RTC.alarmInterrupt(ALARM_1, false);
    RTC.alarmInterrupt(ALARM_2, false);
    RTC.squareWave(SQWAVE_NONE);
 
     // set Alarm 1 to occur at 5 seconds after every minute
    RTC.setAlarm(ALM1_MATCH_SECONDS, 5, 0, 0, 0);
    // clear the alarm flag
    RTC.alarm(ALARM_1);
    // configure the INT/SQW pin for "interrupt" operation (disable square wave output)
    RTC.squareWave(SQWAVE_NONE);
    // enable interrupt output for Alarm 1
    RTC.alarmInterrupt(ALARM_1, true);
    Serial.println(" Start ");
    attachInterrupt(digitalPinToInterrupt(2),printTime,LOW);
}
 
void loop()
{
 
}
// procedure interruption
void printTime()
{
       RTC.alarm(ALARM_1);
       Serial.println("ça marche");
 }
l'appel à l'ISR ne se fait pas,le pin 2 passe bien à 0,mais sans resultat.Quelqu'un a t'il une idée ??